Siemens alarm codes
364 alarms documented. Each entry explains the code, likely causes and the replacement part that resolves it.
SINUMERIK 810/820 legacy alarm
SINUMERIK 840C legacy alarm
- 1Battery: Data loss at power off!
- 101Prewarning replace battery
- 1044*Battery absolute module
- 112*Zero-speed control
- 116*Contour monitoring
- 132*Closed-loop system hardware axis
- 136*Contamination measuring system axis
- 144*Zero mark monitoring responded
- 148*/152*SW limit switch plus / minus
- 2Overtemperature
- 2003*Zero speed monitoring
- 2030*Spindle speed too high
SINUMERIK NCK general alarm
- 1000Hotline alarm
- 1030System error in the link module
- 1031Link module generated an unspecified error
- 14011Channel %1 block %2 program %3 not found
- 14012Channel %1 block %2 maximum subroutine level exceeded
- 15122Power ON after power failure: %1 data were restored, of which %2 machine data, %3 errors
- 2101NCK battery alarm
- 2102NCK battery alarm
- 2110NCK temperature alarm
- 2120NCK fan alarm type %1
- 21305V/24V encoder or 15V D/A converter undervoltage
- 2140The actual service switch position forces the SRAM to be cleared at the next Power On (general reset active)
- 2192No NCU link module exists
SINUMERIK 808D alarm
- 10203[Channel 1: ] NC start without reference point (action=%2<ALNX>)
- 10620[Channel 1: ] Block %3 axis %2 at software limit switch %4
- 2000PLC sign-of-life monitoring
- 2110NCK temperature alarm
- 2140The actual service switch position forces the SRAM to be cleared at the next Power On (general reset active)
- 21610[Channel 1: ] Axis %2 encoder %3 frequency exceeded
SINUMERIK 828D alarm
SINUMERIK channel alarm
- 10600Channel %1 block %2 auxiliary function during thread cutting active
- 10601Channel %1 block %2 zero velocity at block end point during thread cutting
- 10604Channel %1 block %2 thread lead increase too high
- 10605Channel %1 block %2 thread lead decrease too high
- 10607Channel %1 block %2 thread with frame not executable
- 10750Channel %1 block %2 tool radius compensation activated without tool number
- 10751Channel %1 block %2 danger of collision due to tool radius compensation
- 10753Channel %1 block %2 selection of the tool radius compensation only possible in linear block
- 10754Channel %1 block %2 deselection of the tool radius compensation only possible in linear block
- 10757Channel %1 block %2 changing the compensation plane while tool radius compensation is active not possible
- 10758Channel %1 block %2 curvature radius with variable compensation value too small
- 10763Channel %1 block %2 path component of the block in the compensation plane becomes zero
- 10764Channel %1 block %2 discontinuous path with active tool radius compensation
- 10800Channel %1 block %3 axis %2 is not a geometry axis
- 10860Channel %1 block %2 feedrate not programmed
- 10862Channel %1 block %2 master spindle also used as path axis
- 10882Channel %1 block %2 activation of chamfers or radii (non-modal) without traversing movement in the block
- 10883Channel %1 block %2 chamfer or fillet has to be reduced
- 10900Channel %1 block %2 no S value programmed for constant cutting speed
- 10930Channel %1 block %2 interpolation type not allowed in stock removal contour
- 10931Channel %1 block %2 incorrect stock removal contour
- 10933Channel %1 block %2 contour program does not contain enough contour blocks
- 12060Channel %1 block %2 same G group programmed repeatedly
- 12080Channel %1 block %2 syntax error in text %3
- 12140Channel %1 block %2 functionality %3 not implemented
- 12160Channel %1 block %2 range of values exceeded
- 12470Channel %1 block %2 G function %3 is unknown
- 12540Channel %1 block %2 Block is too long or too complex
- 12550Channel %1 block %2 name %3 not defined or option not installed
- 12640Channel %1 block %2 invalid nesting of control structures
- 14011Channel %1 block %2 program %3 not existing or will be edited
- 14012Channel %1 block %2 maximum subroutine level exceeded
- 14015Channel %1 block %2 program %3 is not enabled
- 14040Channel %1 block %2 error in end point of circle
- 14045Channel %1 block %2 error in tangential circle programming
- 14048Channel %1 block %2 wrong number of revolutions in circle programming
- 14051Channel %1 block %2 arithmetic error in part program
- 14080Channel %1 block %2 jump destination %3 not found
- 14090Channel %1 block %2 illegal D number
- 14095Channel %1 block %2 radius for circle programming too small
- 14165Channel %1 block %2 active T number does not match selected tool
- 14200Channel %1 block %2 negative polar radius
- 14800Channel %1 block %2 programmed path speed less or equal to zero
- 14810Channel %1 block %2 negative axis speed programmed for positioning axis %3
- 14815Channel %1 block %2 negative thread lead change programmed
- 14820Channel %1 block %2 negative value for maximum spindle speed programmed with constant cutting speed
- 14900Channel %1 block %2 center point and end point programmed simultaneously
- 14910Channel %1 block %2 invalid angle of aperture for programmed circle
- 14920Channel %1 block %2 intermediate point of circle incorrect
SINUMERIK NCK/HMI communication alarm (PROFIBUS segment)
SINUMERIK axis/spindle alarm
- 20000[Channel %1: ] Axis %2 reference cam not reached
- 20001[Channel %1: ] Axis %2 no cam signal present
- 20002[Channel %1: ] Axis %2 zero mark not found
- 20003[Channel %1: ] Axis %2 measuring system error
- 20004[Channel %1: ] Axis %2 reference mark missing
- 20005[Channel %1: ] Axis %2 reference point approach canceled
- 20006[Channel %1: ] Axis %2 reference point shutdown velocity not reached
- 20007[Channel %1: ] Axis %2 reference point approach requires 2 measuring systems
- 20300[Channel %1: ] Axis %2 orientation not possible
- 21550[Channel %1: ] Axis %2 Travel from hardware limit switch not possible. Reason: %3
- 21613Axis %1 measuring system changing
- 22000[Channel %1: ] Block %3 spindle %2 change of gear stage not possible
- 22010[Channel %1: ] Block %3 spindle %2 actual gear stage differs from requested gear stage
- 22011[Channel %1: ] Block %3 spindle %2 change to programmed gear stage not possible
- 22020[Channel %1: ] Block %3 spindle %2 gear step change position not reached
- 22040[Channel %1: ] Block %3 spindle %2 is not referenced with zero marker
- 22050[Channel %1: ] Block %3 spindle %2 no transition from speed control mode to position control mode
- 22051[Channel %1: ] Block %3 spindle %2 reference mark not found
- 22052[Channel %1: ] Block %3 spindle %2 no standstill on block change