Fagor alarm codes
375 alarms documented. Each entry explains the code, likely causes and the replacement part that resolves it.
CNC 8060/8065/8070 CNC error
- 0001SYSTEM ERROR
- 0003Error when requesting memory. Restart Windows & CNC
- 0004Checksum error in PLC data
- 0005The CNC was not turned off properly, it must be homed
- 0010Error when testing the RAM with battery
- 0014Watchdog detected in last session
- 0017OFF/ON detected due to power outage
- 0021There is no CAN keyboard
- 0104Communication time out
- 0169Safety temperature exceeded. Unit integrity at risk. Contact SAT
- 0170Low battery voltage
- 0172CPU fan stopped. Overtemperature risk. Contact SAT
- 1000The function of instruction requires programming the axes
- 1004Zero spindle speed
- 1005Motion block with zero feed
- 1008Coordinates out of range
- 1026Wrong circular path with the programmed radius
- 1032Spindle position missing for M19
- 1051The axis does not exist or is not available in the channel
- 1061Nonexistent G function
- 1062Incompatible G functions
- 1492There is no digital input associated with the probe (PRBDI1/2)
- 2000Tool radius greater than the arc radius
- 20001Waiting for AUXEND from the PLC
- 2001Profile damaged by tool radius compensation
Fagor legacy CNC error (8025/8040/8020)
- 061Battery error
- 065Probe error during G75 probing
- 070X axis following error
- 075Feedback error at connector A1
- 089Not all axes have been homed
- 094Parity error in tool table or zero offset table G53-G59
- 098Parity error in X axis parameters
- 106Inside temperature limit exceeded
- 120Checksum error recovering machine parameters from EEPROM
CNC 8055 CNC error
- 1000There is no enough path information.
- 1001Plane change in rounding/chamfering.
- 1002Rounding radius too large.
- 1003Rounding in last block.
- 1004Tangential output programmed wrong
- 1005Chamfer programmed wrong.
- 1006Chamfer value too large.
- 1007G8 defined wrong.
- 1008There is no information about the previous path
- 1010Wrong plane for tangent path.
- 1011No radius has been programmed for G15.
- 1015The tool is not defined in the tool table
- 1016The tool is not in the tool magazine
- 1017There is no empty pocket in the tool magazine
- 1018A tool change has been programmed without M06
- 1019There is no tool of the same family for replacement.
- 1032Spindle gear not defined in M19.
- 1033Wrong gear change.
- 1034"S" has been programmed, but no gear is active.
- 1035Programmed "S" too high
- 1036"S" has not been programmed in G95 or in threading
- 1037No "S" has been programmed for G96.
- 1038The spindle has not been oriented
- 1039No "F" has been programmed in G94.
- 1040Canned cycle does not exist
- 1042Wrong parameter value in canned cycle
- 1055Nesting exceeded
- 1057Undefined subroutine
- 1065Beginning of compensation without straight path
- 1066End of compensation without straight path
- 1067Compensation radius too large.
- 1073Motion block with zero speed.
- 1077Either the arc radius is too small or a full circle has been programmed
- 1082The probe signal has not been received
- 1084Arc programmed wrong
- 1085Helical path programmed wrong
- 1086The spindle cannot be homed.
- 1088Range exceeded in zero offset.
- 1090Point inside the forbidden zone 1.
- 1092Insufficient acceleration for the speed programmed in threading.
- 1100Travel limits of spindle 1 exceeded
- 1101Spindle 1 locked
- 1102Following error of spindle 1 out of limit
- 1106Travel limits of spindle 2 exceeded
- 1107Spindle 2 locked
- 1108Following error of spindle 2 out of limit
- 1109Axis software limit overrun
- 1110-1118Range of the * axis exceeded
- 1119-1127The * axis cannot be synchronized
- 1128-1136Maximum feedrate of the * axis exceeded
- 1137-1145Wrong feedrate parameter of the * axis
- 1146-1154* axis locked
- 1155-1163Maximum axis limits of the * axis exceeded
- 1164-1172Work zone 1 of the * axis exceeded
- 1182-1190Following error of * axis out of limit
- 1191-1199Difference of following errors of the slaved axis * too large
- 1200-1208Travel limits of the * axis exceeded
- 1209-1217* axis servo error
- 1218-1226Work zone 3 of the * axis exceeded
- 1249Variable pitch thread programmed wrong
- 2017CNC RAM memory error
- 2018CNC EPROM memory error
- 2021CNC user RAM memory error (Press any key)
- 2025Probe feedback error
- 2026Probe's maximum travel limit overrun
- 2036The type of keyboard does not match the CNC model
- 2041Unsupported LCD type
CNC 8055 servo error
- 1182X axis following error beyond limits (1183-1190 = Y/Z/U/V/W/A/B/C)
- 1191Difference of following errors of the slaved X axis too large (1192-1199 = other gantry pairs)
- 2000External emergency activated.
- 2012There is no voltage at the axis board
- 2016The PLC is not ready.
- 203724 V missing at the CPU-CNC module.
CNC 8055 hardware/feedback error (analog axes)
- 2001X axis feedback error (same block as 2002-2009 for Y/Z/U/V/W/A/B/C)
- 2010Spindle feedback error (2029 = same for spindle 2)
- 2011Maximum temperature exceeded
- 2013There is no voltage at the I/O 1 board.
- 2017CNC RAM memory error.
- 2018CNC's EPROM memory error.
- 2019PLC's RAM memory error.
- 2025Probe feedback error
- 2026Probe's maximum travel limit overrun.
- 2027SERCOS chip RAM memory error.
- 2028SERCOS chip version error.
- 2029Feedback error at spindle 2.
- 2030Feedback over-current error